15″ 5-string Viola Progress

Progress Report for the 15″ Five-string viola:

When I last posted, I had completed the carving of both plates and the garland, but had not begun assembling the corpus.

Bass-Bar

The next step was to install the bass bar. The bass bar is the only fixed, interior brace in violins, violas or cellos. Flatback basses do have some other bracing, but they are a different “branch of the family,” so to speak. All members of the violin family have a bass bar– a spruce brace, which runs “north-south” at a slight angle, nearly parallel to the centerline of the front plate of the instrument, and just inboard of the bass-side f-hole, so that it supports the bass-side foot of the bridge. In a five-string instrument, this becomes an even more critical part as the instrument has a broader range and has to have good support on the bass side, as well as the ability to sing in the higher registers.

I first carve the bass bar bottom to exactly fit the inside curve of the front plate, along the correct location, and at the correct angle, then glue and clamp it in place, using hot hide glue and special clamps, padded with cork, so as not to damage the soft spruce of the front plate.

Fitted, glued and clamped bass-bar on a Five-string viola. — Fitted, glued and clamped bass-bar. Still needs to be shaped.

Proposed general profile of the bass-bar.

Shaping the bass-bar in a Five-string viola, using a finger-plane. — Shaping the bass-bar, using a finger-plane.

Completed shaped of finished bass-bar for a Five-string viola. — Completed shape of finished bass-bar.

Five-string viola corpus assembly:

Now the plates are ready to be installed. Before doing so, I used a small finger plane and half-round files to shape the edge all the way around on the inner face of each plate, hoping to avoid having to shape it after installation. (I am aware that sometimes adjustments have to be made, so I may have to do some tight-clearance work later on, in spite of this precaution. That’s OK.)

The next step was to install the back plate. This is an older-model mold, or “form,” (my first, in fact, as I mentioned in an earlier post) so it has some peculiarities, compared to my newer ones: it is a two-part mold, made to collapse, thus easing removal of the mold after installing the first plate. But in later iterations, I moved toward installing the front plate first, and installing the neck before removing the mold.

In this model, originally, I had planned to install the back plate, then remove the mold, and finally install the front plate, after which I could install the neck whenever I was ready to do so. Nowadays I personally find it easier, however, to install the neck before the back plate is in place, because I don’t have to concern myself with the back side of the heel aligning with the back plate button. (Annnd, it would have been a simple matter of planning, to still do that with this mold, if I had been thinking ahead: just label the front side of the mold as being the side without the screws (which have to be accessible) and you can install the front plate first, then remove the mold after installing the neck; no problem.) However…I wasn’t thinking ahead, and I used the mold exactly as I had originally designed it, so I have no choice, now: I am forced to install the back plate first, remove the mold and then (after shaping the blocks and linings and cleaning the interior of the corpus) install the front plate. So that is what I did. (By the way, in case you are thinking that the shape of the front and back plates are mirror-image of one another, the fact is, they virtually never are exactly mirrored, and are nearly never bilaterally symmetrical even if they were. So the front plate will not fit the back of the mold, and vice-versa.) Ah, well…hindsight, etc.

Here is the back plate, glued in place: the mold is still inside, holding everything rigid. Notice the spalting and curl in the maple back. This is a striking look, and some people love it…others do not.

Back plate of the Five-string viola glued and clamped in place on the garland. — Back plate glued and clamped in place on the garland.

After the back plate glue was dry, I removed the mold, shaped the interior blocks and linings, and cleaned up the interior of the corpus, so that it was ready for the front plate to be installed. I also installed the signed and numbered label, marking this as one of my handmade instruments.

Then I clamped the front plate in place, dry, just as I had done with the back plate, removed a few clamps at a time, and used a thin palette-knife to insert hot hide glue between the plate and the blocks and linings. As soon as I had the glue in place, I quickly replaced whatever clamps I had removed, before the glue could gel.

Once the plate was glued and clamped all the way around, I went back around with a blade, and picked out any gelled, cooled hide-glue that had squeezed out of the joint, so as not to have to deal with it later, in the form of hard, jagged chunks of dry hide glue. Then I tightened the clamps a little, and brushed hot water all around the joint, so as to reconstitute any glue that had gelled too soon, and allow the joint to close even more tightly.

Here is the corpus, all glued together. The next step will be to adjust the overhangs as needed, and lay out the corners so as to begin purfling.

Front plate of the Five-string viola, showing the corpus: assembled, glued and clamped. — Front plate showing: Corpus assembled, glued and clamped.

Beginning Purfling the Five-string viola:

I used to do my purfling before closing the corpus, but I frequently discovered that the rib garland had moved a little, during the removal of the mold…or in some other way, things had changed, and then my plates no longer fit the garland, and I could not change the plates, because I had already installed the purfling…which locks in the shape of the plates, irrevocably (sigh…). So, I began waiting until after the corpus is closed and whatever needed overhang adjustments have been made, and then begin purfling.

I use a two-blade purfling marker to sketch in the location of the twin, parallel cuts needed to make the purfling slot, but I have to sketch the corners in by hand, with a pencil, because the purfling marker will not correctly lay out the corners.

I went ahead and began both the front and the back plates, but got too tired to complete them last night. (Today was spent getting last-minute things done, as we have heard they are mandating that all Oregonians stay at home, due to the coronavirus scare. Went and bought flour and other groceries, filled the car with gas, and got the snow-tires removed, as that deadline is soon upon us as well.)

One thing about the maple and spruce plates: the spruce is very soft, compared to the maple, but it is tricky to carve, because of that. The winter grains (reeds, they are called) are so much harder than the summer reeds, that the blade has a definite tendency to swerve and follow the grain instead of the line you are trying to follow. The maple is much tougher to cut, because it is hard all over, but it is much easier to follow your lines without digressing.

So, here is what the little viola looks like, today:

Back purfling-slot begun on the Five-string viola--far from finished. — Back purfling-slot begun: the dark strip at the top is the only area where I already picked out the slot.

Front purfling-slot begun on the Five-string viola. — Front purfling-slot begun: none of the slot has been picked out.

In both cases, the plan is to cut the two incisions, pick out the wood between them, and then dry-fit the purfling strips, before removing them one-by-one and gluing them in place with hot hide glue.

That will be the next post, unless I take a break and carve the scroll. Either way, it is starting to look like a fiddle!

🙂

Thanks for looking.

March 16, 2020June 2, 2020

Beginning of a “Chez Les Eveques” Five-string fiddle.

Advanced Student Instruments, including Five String Fiddles

A less expensive option:

I had originally hoped to only build “new, made from the raw wood” instruments, but, as it turns out, fewer people are willing (or able) to pay for the labor involved in building such an instrument. So, reluctantly, some years ago, I began to offer “advanced student instruments,” which meant I bought an unfinished instrument “in the white”, and completed the building, finishing and set-up as if it were my own creation, but labeling it as having been “from my shop” (meaning, not made by me,) and selling it at about 1/4-1/3 the price of my handmade instruments. For better or worse, these were a popular option, as the buyer gets a very good violin or viola, for a low price, and a 100% trade-in, if they later decide to buy one of my original handmade instruments. I named the new line of instruments “del Atelier Chez les Eveques” (From the workshop at the Bishops’ place.) I like the sound of it, and it sounds a lot more “bien sophistique” in French, for some reason. 🙂

Five String “Chez Les Eveques”

I recently found that there were now also 5-string instruments available in the white, and, as an experiment, I bought two of them: a five-string fiddle (which seems to simply be a regular violin with a 5-string scroll,) and a 15″ 5-string viola (which, again, seems to be a normal 15″ viola body with a 5-string scroll.)

5-string violin and 5-string viola in the white — 5-string violin and 5-string 15″ viola, in the white.

A good starting place:

As had been my experience in the past, the workmanship is quite good. The rest is up to me, as a rule. I do see some improvements I would make if I were in charge of the factory producing them, but that is OK, too. (Can’t give away all the secrets!)

I began the finishing process as if they were my own work; but with no specific plan, as I had no customer in mind, so I could not ask their preference. Just my usual gound, sealer, and first varnish coats.

five string fiddles early varnish look — Early varnish look for both instruments.

Annnd … a Customer!

I was also in the midst of completing a commissioned instrument, so that was taking priority, but sometime along in the middle, there, I received a message from an individual who wanted this level of five-string fiddle. Annnd, she wanted to see what it looked like as it stood now… I actually had the customer on the phone, when I went into the next room and clumsily took two photos with my phone (see below) and sent them to her.

Five-string fiddle snapshot front — Snapshot of front.

Snapshot of back of Five-string fiddle. — Snapshot of back.

Bingo! She liked it, and said, “Let’s get it done!” So, we were off and running!

I asked questions as to her preferences, saw photos of her current existing instruments, and got a clear idea of where I was going with the look: (fairly deep color, some antiquing, etc.), and I began laying on color to suit, but sending her progress reports with photos, for approval.

Five-string fiddle Varnish getting close to completion. — Varnish getting close to completion.

Once the varnish was nearing completion, I installed the fingerboard and began set-up:

Front view of Five-string fiddle with fingerboard. — Front view with fingerboard.

Back view of Five-string fiddle with fingerboard. — Back view with fingerboard.

Having received assurance that all was well, so far, I continued on into set-up, and completed the instrument.

Front view of Completed Five String Fiddle. — Front view of the completed instrument.

That tailpiece is hand-carved of Osage Orange, per the customer’s request: she was classically trained and does not like the multiple fine-tuners I usually supply.

Side view of the completed Five String Fiddle. — Side view of the completed instrument.

Back view of the completed Five String Fiddle. — Back view of the completed instrument.

Close-up of Five String Fiddle scroll. — Close-up of the scroll.

So…you may be thinking, “How does it sound?“

Well, actually, disgustingly good! I always hope that my handmade instruments are just “head and shoulders above” the ones I buy in the white, but this is really a good five-string fiddle! The main advantage of the handmade original is that the customer gets to choose what type of (and in some cases what specific pieces of) wood will be used, as well as the overall look, and set-up. I can tailor an instrument to the needs of the specific player, if I start from the beginning with that player in mind. Not so much with the factory-made, in-the-white instruments. But, in this case, I think we have a winner!

The customer is a violist, so she knows good viola sound, and will undoubtedly mix and match strings until she finds the perfect match for her, but she is starting off with excellent balance across all five strings: nothing flabby or unfocused about that C-string at all! So, she should be able to put her favorite strings on it and get “instant gratification.” I expect so, anyway… There are so many possible combinations that I can’t say for certain that they will all work. I will ship it with a decent set of strings that work very well, and after that, it is the customer’s game, for life! 🙂

Here is her new baby, hanging in my dining room, ready to ship!

Five String Fiddle Ready to ship — Ready to start a new life!

Thanks for looking.

February 12, 2020June 2, 2020

Completed Five-String Fiddle

Commissioned Five-string fiddle complete.

Five String Fiddle is headed for the Bluegrass Festival!

The customer gave her enthusiastic blessing to my taking her precious new fiddle to the Wintergrass festival; hopefully to be played by some real professionals. Last night I completed most of the set-up, and I had it playing this morning.

So, here is most of the set-up process:

Re-install the fingerboard.
Carve and install the nut (final shaping later.)
Ream peg-holes
Carve and install the saddle.
Install the end button.
Install the soundpost
Install the pegs.
Cut the bridge to proper fit, shape, and height.
Install tailpiece and strings.
Play it for final adjustment of soundpost, bridge, nut height, etc.

As you may recall, the customer chose Ipe wood for fingerboard, nut, and saddle. It is an extremely hard and dense wood, but not a threatened species, so it is still easy to obtain. In fact, the board I purchased was being sold for decking. I actually have some Apitong wood, too, salvaged from a railroad boxcar floor. Also very dense and hard, but not as pretty as Ipe.

The color of the Ipe wood looks good with the Oregon Big Leaf Maple and the Sitka spruce under their varnish. The only finish on the Ipe is a very light rub of linseed oil.

Shaping the nut of the Five-String Fiddle — Shaping the nut of Ipe wood, to match the fingerboard.

Ipe nut and fingerboard of the Five-String Fiddle — Nut and fingerboard installed and cut to preliminary shape.

Peg holes and nut grooves of the Five-String Fiddle — Peg holes reamed and nut grooves located, but not finished.

Pegs installed on the Five-String Fiddle — Pegs shaped, cut and installed.

Ipe saddle installed on the Five-String Fiddle — Saddle, of Ipe wood, installed with radiused corners to prevent cracks.

Bottom view of the Ipe wood saddle on the Five-String Fiddle — Bottom view of the Ipe wood saddle.

Completed end button with tailpiece of the Five-String Fiddle. — Completed end button with tailpiece.

Finished front view of the Commissioned Five-String Fiddle. — Finished instrument front view. End button and pegs are ebony: I can’t obtain Ipe pegs and fittings.

Bass side viw of the finished Five-String Fiddle — Finished bass side view.

Treble side view of the finished Five-String Fiddle. — Finished treble side view.

Finished back view of the Five-String Fiddle. — Finished back view.

Bass side scroll of the Five-String Fiddle. — Bass side scroll.

Treble side scroll of the Five-String Fiddle. — Treble side scroll.

“Playing it in.”

So, at this point, the main thing is to play the instrument as much as possible, so that it settles into its new life as a fiddle, instead of a bunch of pieces of wood! This period is called “play-in”, and there is much controversy as to what is really happening. But my observation is that there are definite positive changes that come about through vigorous playing of a new (or newly restored) instrument. I’m not going to try to “prove it:” it is just my observation and one I feel comfortable acting upon.

Five-String Fiddle Ready to play! — Ready to play!

How does she sound?

So far, so good! Very good, deep C-string tone, and well-balanced across all the strings. I would like a little more volume, and I may do some tinkering with the soundpost to that end, but I have to say, “Not bad for a brand-new fiddle!”

I think it is a winner! (Very pretty, too, but I didn’t do that…the tree did.)

Thanks for looking.

February 3, 2020June 2, 2020

Commissioned 5-string fiddle

5-String Fiddle nearing completion

Custom Made Five-string fiddle Choices

Back in December, I received a commission for a new 5-string “Bluegrass” fiddle. It was to be made on the same form as one of my earlier instruments but have a two-piece, straight-grained Sitka spruce top and a very wild-grained Oregon Big Leaf maple back, sides and neck. The customer specifically requested Ipe for the Fingerboard, saddle and nut. Ipe is extremely hard, dense wood, but not threatened or scarce, as ebony is becoming. It has an odd color when under the knife, and leaves a bright yellow dust when it is scraped or sawn, but it finishes to a nice dark brown and darkens further with age.

Wild Grain Makes for Tough Carving

The last time I posted, I was just beginning the back plate arching. It was tough carving, as it is extremely “wild” flame, and the Big Leaf Maple grain is anything but straight. The result, of course, is some very beautiful wood. But it is hard work, regardless. The blades must be kept razor-sharp, and cuts must be kept shallow in depth.

The purfling requested was not only double purfling (favored by a few of the early masters, especially those of Brescia) but was to include a purfling weave, as well, in the form of a modified “fleur-de-lis.” This is a design I came up with on my first five-string fiddle, and have continued to use, in a variety of forms, ever since.

Five-string fiddle Back Purfling begun — Working on the back purfling slots.

I like the look of the double-purfling and the weave, but it is pretty hard on my hands, as I still do all my purfling inlays by hand. I know a lot of makers use a Dremel-tool, or something similar. Perhaps I eventually will succumb to that “new-fangled” tool as well.

At any rate, here is the back plate, with the purfling complete:

Completed Five-string fiddle back plate — Back plate complete, ready for final scraping and graduation.

Closing up the “Corpus”

I closed up the corpus a few nights ago: all that is left to do before varnishing is to complete the final carving of the neck heel, and all the final edgework, so that the wood is “varnish-ready.”

Closed Five-string fiddle corpus, side view. — Closed corpus, side view. (Note the heel yet to be carved; edgework incomplete.)

Closed Five-string fiddle Corpus Back — Closed Corpus, back view…button still too long; heel uncarved.

Closed Five-string fiddle Corpus, Front view — Closed Corpus, Front view. Corners and edgework still not done.

I will show one more progress report during the varnishing process, and the last for set-up and playing.

Thanks for looking.

January 5, 2020June 2, 2020

Carving the Five-string fiddle Back Plate

Five-string fiddle Inside Complete

Before I could prepare the back plate of this five-string fiddle, I had to complete the rest of the corpus (body of the violin:) First, the inside willow blocks and willow linings had to be tapered and shaped so they are completely smooth. Then, the back of the entire corpus (including the heel of the neck) has to be leveled, so that it will lie flat on the back plate. So, here is the main part of the 5-string violin, with the interior clean and smooth, and the back leveled and flat:

Beginning the Back Plate

I clamped the corpus flat on the back plate billet, then traced around the ribs, using a small washer to establish the correct rib overhang. Then I corrected the corners, using a straightedge and a series of circle patterns. Finally, I cut out the plate “footprint”, and began the arching process. Oregon Big Leaf Maple is a relatively soft maple, but it is still a good deal harder and tougher than Sitka spruce, so the back plate is a lot more work to carve. Here is the beginning:

Beginning Five-string fiddle Back Plate arching. — Beginning Back Plate arching.

In the above photo, the back plate is sitting in a work cradle, so that it will stay in place while I carve it. The Ibex plane in the photo has been slightly modified, to add the palm-fitting handle. This reduces the stress on my fingers and transfers the force to the palm of my hand as opposed to my thumb and forefinger. (To Ibex plane-owners: you will observe that I have removed the adjusting screw and reinstalled it upside down to allow insertion of the maple handle.)

I have been on vacation for two weeks, which has allowed me to accomplish more work than usual, in a shorter period of time. I go back to my regular job, on Monday, though, so things are about to slow to a crawl. (Sorry…that’s life. :-))

Thanks for looking.

January 4, 2020June 2, 2020

More 5-string Fiddle Progress

Five-String Fiddle Progress

(Further progress on building a custom-made 5-string bluegrass fiddle.)

Neck Set

The neck was ready to set into the neck-block, late last night, but I had reached my physical limit. So, today, I prepared both the neck and the garland, by ascertaining that all angles and dimensions were correct, and then laying out the shape of the neck mortise on the neck block of the garland. This is a critical step in violin-making and always raises my blood pressure a little, as I know that, if I make a mistake, it will require serious rework to get back to a usable status.

However, this time, the job went pretty smoothly, and I was able to set the neck in a fairly short time. One thing I do a little differently than I was originally taught, is that I set the neck before installing the maple back plate. This allows me to achieve a good fit with the rib garland and neck block, and not have to worry about the fit against the back plate button. Then I saw off the stub of the neck heel, and plane and file it flush with the rib garland. After I remove the mold and add the back linings, I will level the back of the garland, and be ready to trace the back plate shape.

Five-string fiddle neck Set Complete. — Neck Set Complete: still have to remove the neck-heel stub.

Here is the completed corpus (Sitka Spruce top plate and Big Leaf maple ribs still on the mold) with the wild-grain Big-leaf maple back plate billet.

Completed Corpus of Five-string fiddle with Back Plate Billet. — Completed Corpus with Back Plate Billet.

Mold Removal

So, the next step was to remove the plywood mold. This is another stressful step because it involves literally using a hammer and chisel, to break the glue-bond between the blocks and the mold, so as to release the garland from the mold. I used to have a difficult time doing this, because occasionally a drop of hide glue had seeped between the rib and the mold, and anchored the fragile rib material to the very solid mold. The likelihood of breaking a rib at that point became nearly 100%. Eventually, however, I learned to liberally coat all the non-gluing surfaces of the mold with candle-wax (paraffin,) by vigorously rubbing a candle over all the areas I felt were likely to get a drop of glue on them.

The result today was that, when I removed the mold, it went smoothly, and I could see a place where glue had definitely intruded but it had dried with zero adhesion to the waxy mold. (What a relief!)

Five-string fiddle mold removed, ready for back linings. — Mold removed, ready for back linings.

Installing the Back Linings

The linings are important for two reasons: they strengthen the fragile rib-edges, and they triple the gluing surfaces between the rib-garland and the front and back plates.

So, I cut the mortices in both sides of each of the six blocks to receive the lining strips, and then inserted the linings dry, to get a perfect fit.

Afterward, I removed each lining, one by one, coated them liberally with hot hide-glue, and re-inserted them, clamping immediately with small spring-clamps.

Five-string fiddle back linings installed, glued and clamped. — Back linings installed, glued and clamped.

Shaping Blocks and Linings

If you look closely you can also see, in the above photos, that I had trimmed the blocks on the front side, before removing the mold. After the glue is dry on the back linings, I will also trim the back side of the blocks, to achieve a smooth, curved surface on the interior of all the blocks. At that same time, I will taper the linings so that they are very thin on the edge toward the middle of each rib, but still 2 mm thick at the edge where they will contact the back and front plates.

After that, it will be time to level the back surface of the entire corpus (garland and neck-heel) so as to fit tightly against the back plate billet. Then I can trace the final shape of the back plate, cut it to shape, and get going on completing the back plate.

For now, I am satisfied to allow the glue to dry, and take the rest of the evening off.

Thanks for looking.

January 3, 2020June 2, 2020

Commissioned Handmade Five-string Fiddle Beginning

Starting a new 5-String Fiddle

The Materials:

A few weeks ago I announced that a new fiddle would be beginning. Now I have a few photos to show:

The top plate is Sitka Spruce, from Bruce Harvie. The customer wanted “Oregon wood,” and the Big Leaf Maple is definitely from in my neighborhood, here in Oregon (I helped harvest it;) but the Sitka is just a species that grows here…I don’t know where it was harvested.

Wild-grain Big Leaf Maple for Five-string fiddle back and ribs! — Wild-grain Maple for back and ribs!

Fine-grained Sitka Spruce for Five-string fiddle top plate. — Fine-grained Sitka Spruce for the top plate.

Preview of the grain in the Five-string fiddle neck billet. — Preview of the grain in the neck billet.

Beginning the work of building a 5-string fiddle:

I book-matched the spruce, to form the basis for the front plate: a solid plate with a tight glue-line down the center.

I used the mold (or form, as many people prefer to call it) that matched the fiddle the customer liked best. Then I added willow blocks to become the corners and end-blocks, and I traced the intended shape of the blocks from the mold template onto the back-side of the blocks, where they are flush with the mold.

Blocks and mold with Five-string fiddle template. — Blocks and mold with template.

Five-string fiddle Preliminary block-shaping complete. — Preliminary block-shaping complete.

Added the ribs, of the spalted maple the customer liked, and glued them to the willow blocks. Afterward, I added linings, also of willow, and let them into the blocks and glued them to the ribs and the blocks.

Spalted Maple ribs and willow linings on beginning of Five-string fiddle. — Spalted Maple ribs and willow linings.

Five-string fiddle Rib garland nearly complete. — Rib garland nearly complete.

Then I traced the shape of the garland onto the top plate material, using a small washer as a spacer, and a ball-point pen as a scribe. I completed the corners using a straightedge and a series of circle templates. Finally, I marked the edge at exactly 4 mm thick, and carved the arching, using gouges and planes and scrapers.

Sitka top-plate arching complete for Five-string fiddle. — Sitka top-plate arching complete.

Then I marked the layout of the double purfling and the f-holes, and began incising them into the Sitka Spruce.

F-holes and purfling traced and cutting begun for Five-string fiddle. — F-holes and purfling traced and cutting begun.

Sometime in the midst of all the above work, I laid out and began carving the scroll and pegbox. That wild grain is very tricky to carve, as it changes direction constantly.

Rough-carved scroll and pegbox of Five-string fiddle. — Rough-carved scroll and pegbox.

I went ahead and completed the purfling and the f-holes, so that I could prepare the plate to be glued to the garland.

Completed top plate and neck work with garland for Five-string fiddle. — Completed top plate and neck work with garland.

I also added the bass-bar, chalk-fitting it to perfection, and gluing it in place, with hot hide glue. The bass-bar will be carved, planed and scraped to the proper shape after the glue dries.

Five-string fiddle Bass-bar glued and clamped. — Bass-bar glued and clamped.

Five-string fiddle Top plate glued and clamped to the garland, fingerboard glued to the neck. — Top plate glued and clamped to the garland, fingerboard glued to the neck.

The fingerboard is Ipé, as requested by the customer. It is an extremely dense hardwood, but not threatened as Ebony is beginning to be. It finishes to a dark brown and looks good, as well as wearing well. It is extremely difficult to work, though, so it may take time to become popular with makers. The saddle and the nut will also be Ipé, but the pegs will be ebony, simply because I have never mastered the lathe-turning of tuning pegs.

Working on the fingerboard for the Five-string fiddle. — Working on the fingerboard.

And that is pretty much where things stand, for now. I will try to post pictures as they become available.

Thanks for looking.

December 15, 2019June 2, 2020

New 5-string Commission on the Way!

New Five-String Fiddle Request!

A client contacted me through this website and asked whether I could build a 5-string fiddle of primarily Oregon woods. (Sure!)

Test-Drive of existing fiddles

We made an appointment and she came for a visit. She played eight of my hand-made instruments (all good fiddles), finally declaring a particular one to be exactly what she wanted, except that she did not care for the look of the one-piece Sitka Spruce top plate. It had very wide grain on the bass side and narrower on the treble side. (It sounds great, but the looks were bothering her.) Soooo…

Custom-made Five-string!

I went into my storage and retrieved a really wild-grained piece of Big Leaf Maple, and two billets of very straight, even-grained Spruce: one of Englemann, and another of Sitka: she chose the Englemann and loved the maple. She wanted an instrument essentially the same as that first one, but without the odd-looking belly grain. (The same model; made on the same mold (form), and sounding just like it, as well.) It will be tough to do, because the one she really likes is already five years old; it has had time to settle, be re-adjusted, and settle again. (Yes, it sounds good!)

Select Woods and a Good Start

So, we went out to one of my other buildings and hand-picked some likely-looking wood for the neck and ribs, and we were ready to do business. She presented a deposit, and I suggested that she take home the one she loved, for the time being, to keep her interest up while waiting for me to complete her personal treasure. She went home happy, and I began sorting willow for blocks, finding my proper templates, and enjoying the prospect of a new five-string fiddle build. I will post follow-ups as they occur.

Thanks for looking.

I will post this over on the Bluefiddles page, as well.

July 16, 2019December 15, 2019

Five String Fiddles in the White

“Shop-made” 5-strings

Not my preference, but…

There are folks who want a five-string fiddle, and who can’t justify the expense of a hand-made instrument, made by an American luthier. I completely understand that, so I am going to try an experiment of sorts: I bought two instruments in the white …unvarnished, incomplete, etc. One is a five-string violin (standard size), with a one-piece back, and the other is a 15″ 5-string viola.

five string fiddles in the White — A 5-string violin and a 15″ 5-string viola.

The viola looks much larger than the violin in this photo, but, in reality, the body is 1-1/16″ longer than that of the violin, with a proportionately larger neck and scroll.

Possible Glitches

I can see some potential problems, and I will see whether I can correct them before completing the instruments. There are certain details necessary to a good instrument that have been overlooked in these two. Specifically, it is needful to arrange the locations of the pegs in such a way that the higher strings do not rub on the pegs that are lower in the box. Both of these instruments fail that test pretty badly, but other than that, they seem to be very well-made, if possibly a little heavy.

Up until now, I have only bought standard, four-string instruments-in-the-white, and they have all turned out quite well. I hope I can make these two turn out to be great instruments, too, but… as I said, this is an experiment, of sorts.

At any rate, I will go over them carefully to try and bring them up to my standards as far as those things go. The workmanship is very good, though: I hope they sound great. I guess we will have to wait and see.

Shop Instruments, as a Principle

The advantage of using an imported, unfinished instrument like this, is that it drastically reduces my labor investment, and I can pass the savings on to customers who want a good instrument, but may not want to spend so much.

I label my shop instruments as “Atelier Chez les Eveques“, (the Shop at the Bishops’ Place.) Unlike my handmade personal instruments, they are not signed or numbered. But they are good instruments, and all who have bought them have been well-satisfied.

I will show progress on these two instruments as time permits. (We have had a host of home-repairs to worry us, lately….)

Thanks for looking.

June 22, 2019June 22, 2019

June 22nd Progress Report

Some Progress is better than none!

It has been a frustrating series of weeks: all the usual responsibilities, house guests, etc., plus a few unexpected items. The lawn tractor suddenly quit mowing, though it ran fine. We narrowed it down to being a bad PTO clutch, so that is just another thing to take apart and replace. Guess that’s what happens when you use 30-year-old equipment. 🙂

Then, two days ago, my beloved better half, Ann, discovered that the side porch steps are in advanced stages of rot…so, today, we went and bought all the pressure-treated lumber to replace them. They, too, have been in place for over 30 years, so, I guess, they have served well.

Progress on the 5-String Fiddles

I did manage to make a little progress on some of the acoustic five-string fiddles I had begun, however:

All the linings are in place for two of the instruments (violin and the 14-7/8″ viola.)
The front and back plates are traced and cut out for both of those instruments.
The front plate graduations are complete for the 14″ viola, and
The f-holes are cut out on the 14″ viola, but not refined.

So, this is where things stand, at the moment:

Here is the “Strobelesque” garland with its front and back plates:

garland and plates — Rib Garland and rough-cut plates for the “Strobelesque” fiddle.

No carving at all has been done on the plates, and the Sitka Spruce front plate is still nearly an inch thick. I will plane it down before I begin arching, of course. I do like the look of the spalted maple back and ribs. This maple was from an old Big Leaf Maple tree on the property where Ann grew up. It had begun to show signs of decay, and was removed for safety’s sake. Too bad for the loss of the tree, but it is nice wood.

Here is the 14-7/8″ Viola garland with its front and back plates.

garland with plates — Rib garland with front and back plates for a 14-7/8″ 5-string viola.

This one is my own design. In fact, it was the very first form I ever made, thinking I was just going to make a viola for my youngest son (whose name is on the form, along with the date: 1999.) As it happened, I discovered that lutherie is addictive, and I have been building instruments ever since. 🙂

The center-lines on both plates are ink, not a glue-line: this instrument boasts both a one-piece Spalted (Big-Leaf) Maple back plate (also from the tree at Ann’s childhood home) and a one-piece Sitka Spruce front plate.

Here is the progress on the 14″ Viola:

This one is my own design, too: it is the same length as a standard violin, but much wider in the lower bouts, and deeper in the ribs. It will be interesting to see how it works as a five-string fiddle. (This is a first.) This one has an Englemann Spruce front plate and a one-piece Big Leaf Maple back from a log I was given by Terry Howell, years ago.

I will post more reports as the work takes place. Feel free to contact me if you have questions.

Thanks for looking.